您好，欢迎来到泰亚赛福！收藏泰亚赛福
泰亚赛福

热门搜索：溶氧仪四合一气体检测仪硬度计测厚仪测温仪
首页 > 工程物探测绘 >  阴极防护/腐蚀控制 > 腐蚀控制产品 > 环氧树脂涂料 > Tapecoat7000高温环氧底漆
Tapecoat7000高温环氧底漆
Tapecoat7000高温环氧底漆
订货号： MM-80549-00
产地： 美国
品牌：
开发编号： N
市场价：￥
*此产品根据配置不同价格不同
*此价格为参考价格，具体价格以订单合同为准
    我在现场：
    产品视频：

所有产品分类

工程/物探/测绘仪器

阴极防护/腐蚀控制

  • 产品描述
  • 技术参数
  • 技术文档
  • 相关产品
  • 明细价格
  • 购买流程
产品描述：

Tapecoat TC 7000 High-Temperature Epoxy is a surface tolerant two-component 100% solids material that replaces VOC base primers. It is manufactured to be used as a one-coat wet or dry primer with Tapecoat hot and cold applied tapes. 
TC 7000 can also be applied as a stand-alone coating for metal surfaces above or below ground, where it provides superior corrosion protection and exceptional flow characteristics with self-leveling attributes.
Use as a single coat primer prior to wrapping with Tapecoat hot or cold applied tapes.
Use as a stand-alone coating on metal surfaces. For added impact and abrasion resistance, use TC reinforcing scrim. ,
Technical Data
Color, Red
Pot Life, 15 to 20 minutes @ 70°F (21°C) and 50% relative humidity (R.H.)
VOC's, Zero
Mix Ratio, 3.54:1 by volume
Red Label, Not required
Application
Surface must be clean and dry. Commercial blast to SSPC-SP6. Remove oil and grease with a suitable solvent. Salt and other contaminants may be removed by high-pressure fresh water cleaning.
Pour entire contents of Part B Curing Agent (small container) into Part A Resin (large container)/ Mix thoroughly for approximately  3 to 5 minutes. Do not alter the amounts of A and B in the mixture.
Apply epoxy by brush, pad, roller or spray. Primer should be dry to touch before applying Tapecoat hot-applied tapes or sleeves.
Tapecoat rpolyethyleneeinforcing scrim can be applied over wet epoxy to add reinforcement and impact resistance. After the scrim has been applied, apply a second coat of TC 7000 Epoxy.
Application Parameters
Environment, Use only when the surface to be coated is above 40°F (4°C) and the relative humidity (R.H.) is less than 90%.
Application Temperature, 40°F-200°F (4°C-93°C). Surface temperature must be 5°F (3°C) above dew point to avoid condensation. 
Cure Time, 60 to 90 Minutes at 70°F - 80°F (21°C-27°C) and 50% R.H. Cure time can be accelerated by preheating the metal surface to 100°-200°F (38°-93°C).
Recommended Coverage , As a 1-Coat Primer: 6-10 mils thickness, with a coverage of 220 sq. ft. per mixed gallon (5.4 m2 per liter). 
As a 2-Coat Stand-alone Coating with Scrim: 16-30 mils (0.41-0.76 mm) thickness. This is 2 coats of 8-15 mils (0.20-0.38 mm) each).
 
Container Size
Coverage as a 1-coat primer at 6 mils
Coverage as a 2-coat coating 
at 12 mils
Pint can base (Part A) and 1/2 pint can cure
(Part B), total mixed volume: 1.5 Pints.
45 sq. ft.
22.5 sq. ft.
Quart can base (Part A) and Pint can cure
(Part B), total mixed volume: 1.5 qt.
90 sq. ft.
 45 sq. ft.
Gallon can base (Part A) and 2 qt. cans cure
(Part B), total mixed volume: 1.5 Gallons.
360 sq. ft.
180 sq. ft.
 


品牌简介

美国MI美国MI
品牌详情>>

您最近浏览的商品

美国泰亚赛褔