|
Specifications |
Model 4040DDS |
|
Frequency Characteristics (Standard Waveforms) |
|
Sine |
0.1 Hz to 20 MHz |
|
Square |
0.1 Hz to 20 MHz |
|
Triangle, Ramp |
0.1 Hz to 2 MHz |
|
Accuracy |
0.01% (100 ppm) |
|
Resolution |
4 digits or 10 mHz |
|
Output Characteristics |
|
Amplitude Range |
10 mV to 10 Vp-p into 50 Ω |
|
Resolution |
3 digits (1000 counts) |
|
Amplitude Accuracy |
±2% ± 20 mV of the programmed output from 1.01 V - 10 V |
|
Flatness |
0.5 dB at 1 MHz
1 dB to 20 MHz |
|
Offset Range |
±4.5 V into 50 Ω, depending on the Amplitude setting |
|
Offset Resolution |
10 mV with 3 digits resolution |
|
Offset Accuracy |
±2% ± 10 mV into 50 Ω |
|
Output Impedance |
50 Ω |
|
Output Protection |
The instrument output is protected against short circuit or accidental voltage practically available in electronic laboratories, applied to the main output connector |
|
Waveform Characteristics |
|
Harmonic Distortion |
0 - 20 kHz, -50 dBc
20 kHz - 100 kHz, -45 dBc
100 kHz - 1 MHz, -40 dBc
1 MHz - 20 MHz, -30 dBc |
|
Spurious |
DC - 1 MHz, < -55 dBc |
|
Square Rise/Fall Time |
< 20 ns (10% to 90%) at full amplitude into 50 Ω |
|
Variable Duty Cycle |
20% to 80% to 2 MHz for Square and 10% - 90% for Triangle |
|
Symmetry at 50% |
< 1% |
|
Operating Modes |
|
Continuous |
Output continuous at programmed parameters. |
|
Triggered |
Output quiescent until triggered by an internal or external trigger, then one waveform cycle is generated to programmed parameters, up to 2 MHz |
|
Gate |
Same as triggered mode, except waveform is executed for the duration of the gate signal. The last cycle started is completed. |
|
Trigger Source |
Trigger source may be internal, external or manual. Internal trigger rate 10 µs to 10 s. |
|
Modulation Characteristics |
|
Amplitude Modulation |
|
|
Internal |
Sine signal of 1000 Hz
Variable modulation from 0% to 100% in 1% steps |
|
External |
5 Vp-p for 100% modulation, 10 kΩ input impedance, DC to 20 kHz bandwidth. |
|
Frequency Modulation |
|
|
Internal |
Sine signal of 1000 Hz |
|
External |
5 Vp-p for 100% deviation, 10 kΩ input impedance, DC to 20 kHz bandwidth. |
|
Sweep Characteristics |
|
Sweep Shape |
Linear and Logarithmic, up or down |
|
Sweep Time |
10 ms to 50 s. |
|
Inputs and Outputs |
|
Trigger In |
TTL compatible.
Max. rate 2 MHz.
Minimum width 50 ns. |
|
Sync Out |
TTL pulse at programmed frequency, 50 Ω source impedance. |
|
Modulation In |
5 Vp-p for 100% modulation.
10 kW input impedance. DC to > 20 kHz minimum bandwidth. |
|
General |
|
Dimensions |
8.4'' (213 mm) wide
3.5'' (88 mm) high
8.3'' (210 mm) deep |
|
Weight |
Approx 2.5 kg. |
|
Power |
90 V - 264 V, 30 VA max |
|
Temperature |
|
|
Operating |
0°C to +50°C |
|
Non-operating |
-10°C to +70°C |
|
EMC |
According to EN55011 for radiated and conducted emissions. |
|
Electrical Discharge Immunity |
According to EN55082 |
|
Safety Specifications |
According to EN61010 |
|
Note: Specifications are verified according to the performance check procedures in the technical manual.
Specifications not verified in the manual are either explanatory notes or general performance characteristics only |
泰亚赛福 —— 世界领先的检测仪器集成供应商 
您当前的位置：
加入对比
