| 
 Specifications  | 
 Model 4040A  | 
| 
 Frequency Characteristics  | 
    | 
| 
 Waveforms  | 
 Sine, Square, Triangle, +-Pulse, +-Ramp  | 
| 
 Range  | 
 0.2Hz to 20 MHz in 8 ranges  | 
| 
 Resolution  | 
 5 digits  | 
| 
 Tuning Range  | 
 10:1  | 
| 
 Fine  | 
 +-5% of coarse setting  | 
| 
 Variable Duty Cycle  | 
 15:85:15 cont variable  | 
| 
 Operating Modes  | 
 Normal, sweep, VCG, AM, FM, burst  | 
| 
 Output Characteristics  | 
    | 
| 
 Impedance  | 
 50 W +- 10%  | 
| 
 Level  | 
 20 V p-p Open circuit, 10V p-p into 50 W  | 
| 
 Amplitude  | 
 Variable, 20 dB range typical  | 
| 
 Attenuation  | 
 -20 dB +- 1 dB  | 
| 
 DC Offset  | 
 Preset +- 0.1 V type Variable: +- 10V open-circuit +-5 into 50 W  | 
| 
 SINE Wave  | 
    | 
| 
 Distortion  | 
 <=3% typical at 1 kHz  | 
| 
 Flatness  | 
 +-5% +-(.45 dB) 0.1 Hz to 8 MHz  | 
| 
    | 
 +-20% +-(2.0 dB) 8 MHz to 20 MHz  | 
| 
 Square wave  | 
    | 
| 
 Symmetry  | 
 0.2 Hz to 100 kHz < 2%  | 
| 
 Rise time  | 
 <= 30 ns  | 
| 
 Triangle Wave  | 
 Linearity: >= 98% to 100 kHz  | 
| 
 TTL Output  | 
    | 
| 
 Level  | 
 0.8V to 2.4V  | 
| 
 Rise time  | 
 <= 20 nS  | 
| 
 Duty Cycle  | 
 50% typical  | 
| 
 CMOS Output  | 
    | 
| 
 Max. Frequency  | 
 2 MHz  | 
| 
 Level  | 
 4V to 14V +-0.5 p-p cont. variable  | 
| 
 Rise Time  | 
 <= 120 nS  | 
| 
 VCG (Voltage controlled generator)  | 
    | 
| 
 Input Voltage  | 
 0-10V +- 1V causes a 100:1 frequency change  | 
| 
 Impedance  | 
 10k W +-5%  | 
| 
 Mode  | 
 LIN/LOG  | 
| 
 Width  | 
 100:1 continuously variable  | 
| 
 Rate  | 
 20 ms to 2 s cont variable  | 
| 
 Sweep Output  | 
 0 to 2V  | 
| 
 Start/Stop Frequencies  | 
 Adjustable  | 
| 
 Frequency Counter  | 
    | 
| 
 Accuracy  | 
 Time base accuracy +- 1 count  | 
| 
 Time Base Accuracy  | 
 +- 10 ppm (23 0 +-5 0 C)  | 
| 
 Display  | 
 5 digit LED  | 
| 
 Mode  | 
 INT or EXT  | 
| 
 External Input  | 
    | 
| 
 Frequency  | 
 5 Hz to 30 MHz  | 
| 
 Resolution  | 
 0.1, 1, 10, 100, 1 kHz  | 
| 
 Sensitivity  | 
 25Vrms  | 
| 
 Power Source  | 
 120/230 VAC +-10% 50/60 Hz, internal jumper selectable  | 
| 
 Dimensions  | 
 5.5x11.75x10.575'' (140x298x264)  | 
| 
 Weight  | 
 4.5 lbs. (2 kg)  | 
| 
 AM MODULATION CHARACTERISTICS  | 
| 
 Source  | 
 Internal, External  | 
| 
 Modulation Ratio  | 
 0 to 100%  | 
| 
 Int modulation  | 
 1 kHz  | 
| 
 Ext Modulation  | 
 DC to 500 kHz  | 
| 
 Ext Sensitivity  | 
 Less than 10V p-p for 100% modulation  | 
| 
 FM MODULATION CHARACTERISTICS  | 
| 
 Source  | 
 Internal, External  | 
| 
 Modulation Ratio  | 
 0 to 100%  | 
| 
 Deviation  | 
 0 to 5%  | 
| 
 INT Modulation  | 
 1 kHz  | 
| 
 Ext Modulation  | 
 DC to 500 kHz  | 
| 
 Ext Sensitivity  | 
 Less than 10V p-p for 100% modulation  | 
| 
 BURST CHARACTERISTIC  | 
| 
 Source  | 
 Internal, External  | 
| 
 Burst Width  | 
 Cont. variable from 5% to 90% of internal gating frequency  | 
| 
 Repetition Rate  | 
 0.5 Hz to 50 Hz, internal  | 
| 
    | 
 DC to 500 kHz external  | 
| 
 External Level  | 
 TTL levels  | 
| 
 Burst Frequency  | 
 Determined by main generator frequency setting.  | 
| 
 Two Year Warranty  | 
| 
 Accessories  | 
| 
 SUPPLIED: Output Cable with BNC to Alligator Clips, Instruction Manual Carrying Case (not included): LC-40  |