泰亚赛福 —— 工业设备集采平台
PT295 Series可燃气体传感器…
PT205 Series可燃气体传感器…
Ultra1000硫化氢传感器
PT395硫化氢传感器
PT295硫化氢传感器2009/10/21 14:46:17 阅读：483次
|
Features
Low Maintenance.
4-20mA Analog Output
Optional RS485 MODBUS RTU Serial Communication
12-28 VDC Operation
Automated Non-Intrusive Calibration
Optional Adjustable Alarm Relay Contacts
Liquid Crystal display with back light
Description
Ultra 1000-IR series is a microprocessor based sensor for detection of Carbon Dioxide (CO2) gas using Infrared sensor technology. The self- contained sensor features user friendly interface and menu driven calibration procedure and configuration.
Ultra 1000-IR uses NDIR (Non Dispersive Infrared) technique to monitor the CO2 vapors. The detection principle is based on measuring the absorption of infrared radiation using dual wavelength infrared detectors. The IR detectors measure the intensity of two wavelengths, one absorbed by the target gases and other unaffected by the target gases. The gas concentration is determined by comparing the detector signals.
The complete sensor consists of a stainless steel sensor head assembly, a user connection board and a transmitter board assembly. All of the sensor electronics are enclosed in an explosion proof instrument box. Ultra 1000-IR provides a 4-20mA signal proportional to 0-100% LEL gas at the sensor. In addition the sensor may be addressed via MODBUS RTU interface. The MODBUS output provides sensor status, alarm & fault conditions.
Specifications
Sensor Type
NDIR (Non Dispersive Infrared) absoprtion
Measuring Range
0-5% , 0-10% & 0-50%
Repeatability
± 2 % Full scale
Zero Drift
< 2% per year
Response Time
T50 < 8 seconds T90 < 15 seconds with 100% LEL gas applied
Classification
Class I, division 1, Groups B,C & D
Operating Temperature
-40°F to +158°F (-40°C to +70°C)
Operating Humidity
5% to 90% RH, non-condensing
Display
2 lines by 8 Character LC Display with back light
Mechanical Specifications
Length: 7 inches (178 mm)
Width: 5 inches (127 mm)
Height: 4.5 inches (114 mm)
Status Indicators
LC Display for gas concentration, Alarm relay status, calibration mode and sensor fault status.
Input Power
14-28 VDC. 24 VDC nominal
Power Consumption
90mA @ 24 VDC Typical
Alarm Relays
Fully programmable. 0 to Full scale range of the sensor. Latching or Non-Latching.
Relay Ratings
SPDT Form “C” type Relay contacts
5 Amps @ 250 VAC or 30 VDC
Analog Output
Linear 4-20mA (300 Ohms max. load)
2.0 mA - Calibration mode
< 1.0 mA - Sensor malfunction
Interface
RS-485 MODBUS RTU at 9600 Baud.
Calibration
Non-Intrusive activated by internal magnetic switch
Features
Low Maintenance.
4-20mA Analog Output
Optional RS485 MODBUS RTU Serial Communication
12-28 VDC Operation
Automated Non-Intrusive Calibration
Optional Adjustable Alarm Relay Contacts
Liquid Crystal display with back light
Description
Ultra 1000-IR series is a microprocessor based sensor for detection of Carbon Dioxide (CO2) gas using Infrared sensor technology. The self- contained sensor features user friendly interface and menu driven calibration procedure and configuration.
Ultra 1000-IR uses NDIR (Non Dispersive Infrared) technique to monitor the CO2 vapors. The detection principle is based on measuring the absorption of infrared radiation using dual wavelength infrared detectors. The IR detectors measure the intensity of two wavelengths, one absorbed by the target gases and other unaffected by the target gases. The gas concentration is determined by comparing the detector signals.
The complete sensor consists of a stainless steel sensor head assembly, a user connection board and a transmitter board assembly. All of the sensor electronics are enclosed in an explosion proof instrument box. Ultra 1000-IR provides a 4-20mA signal proportional to 0-100% LEL gas at the sensor. In addition the sensor may be addressed via MODBUS RTU interface. The MODBUS output provides sensor status, alarm & fault conditions.
Specifications
Sensor Type
NDIR (Non Dispersive Infrared) absoprtion
Measuring Range
0-5% , 0-10% & 0-50%
Repeatability
± 2 % Full scale
Zero Drift
< 2% per year
Response Time
T50 < 8 seconds T90 < 15 seconds with 100% LEL gas applied
Classification
Class I, division 1, Groups B,C & D
Operating Temperature
-40°F to +158°F (-40°C to +70°C)
Operating Humidity
5% to 90% RH, non-condensing
Display
2 lines by 8 Character LC Display with back light
Mechanical Specifications
Length: 7 inches (178 mm)
Width: 5 inches (127 mm)
Height: 4.5 inches (114 mm)
Status Indicators
LC Display for gas concentration, Alarm relay status, calibration mode and sensor fault status.
Input Power
14-28 VDC. 24 VDC nominal
Power Consumption
90mA @ 24 VDC Typical
Alarm Relays
Fully programmable. 0 to Full scale range of the sensor. Latching or Non-Latching.
Relay Ratings
SPDT Form “C” type Relay contacts
5 Amps @ 250 VAC or 30 VDC
Analog Output
Linear 4-20mA (300 Ohms max. load)
2.0 mA - Calibration mode
< 1.0 mA - Sensor malfunction
Interface
RS-485 MODBUS RTU at 9600 Baud.
Calibration
Non-Intrusive activated by internal magnetic switch
|
| 产品编号 | 产品名称 | 产品简介 | 产品价格 |
|---|---|---|---|
| MR-00208-00 | Carbon Dioxide CO2 Sensor | 0￥ |
您当前的位置：
加入对比
