| |
OS-3020D |
OS-3040D |
OS-3060D |
| CRT阴极管 |
配置和有效视频 |
6 inch rectangular screen with internal graticule: 8x10DIV (1div=1cm), marking for measurement of rise time. 2mm subdivisions along the central axis. |
| 加速电势 |
+1.9kV approx |
+11.5kV approx |
+11.5kV approx |
| 荧光器 |
P31 (Standard) |
| 聚焦 |
Possible (with auto - focus correction circuit) |
| 旋转线迹 |
provided |
| 比例照明 |
Variable |
| 亮度控制 |
provided |
| 高强度Z轴输入 |
输入信号 |
Positive going signal decreases intensity + 5Vp-p or more signal cases noticeable modulation at normal intensity settings |
| 频宽 |
DC to 2MHz (-3dB) |
| 触发耦合 |
DC |
| 输入阻抗 |
20kOhm - 30kOhm typical |
| 最大输入电压 |
30V (DC + peak AC) |
| 垂直偏转 |
频宽 |
(DC Coupled)
DC to 20MHz normal
DC to 7MHz magnified |
DC to 40MHz normal
DC to 7MHz magnified |
DC to 60MHz normal
DC to 10MHz magnified |
| 模式 |
CH1,CH2,DUAL,ADD (CHOP: Time/div switch -0.2s to 5ms, ALT: time/div. switch -2ms to 0.2us) |
CH1,CH2,DUAL,ADD (CHOP: Time/div switch -0.2s to 5ms, ALT: time/div. switch 2ms to 0.1us) |
| 偏转系数 |
5mV/div to 5V/div in 10 calibrated steps of a 1-2-5 sequence.
Continuously variable between steps at least 1:2:5
(x5 MAG : 1mV/div to 1V/div 10 calibrated steps) |
| 准确度 |
Normal: +/-3%, magnified: +/-5% |
| 输入阻抗 |
Approx, 1Mohm in parelle1 with 25pF+/-3pF |
| 最大输入电压 |
Direct 250V (DC + AC Peak) (with probe: refer to probe specification) |
| 输入耦合 |
DC- GND - AC |
| 延升时间 |
17.5ns or less (50ns or less: x5) |
8.8ns or less (50ns or less: x5) |
5.8ns or less (35ns or less: x5) |
| 通道1 输出 |
20mV/div into 50ohm : DC to 10MHz (-3dB) |
| 极性逆向 |
CH2 only |
| 信号延时 |
Delay cable supplied for OS-3040D / OS-3060D |
| 水平偏转 |
显示方式 |
A, A int B, B, TRIGD, X-Y |
| A 时基 |
0.2us/div to 0.2s/div in 19 calibrated steps 1-2-5 sequence, uncalibrated continuous control between steps at least 1:2:5 |
0.1us/div to 0.2s/div in 20 calibrated steps 1-2-5 sequence, uncalibrated continuous control between steps at least 1:2:5 |
| 锁定时间 |
Variable with the holdoff control |
| B 时基 |
0.2us/div to 20us/div in 7 calibrated steps 1-2-5 sequence |
0.1us/div to 0.2us/div in 20 calibrated steps 1-2-5 sequence |
| 延时扫描 |
1 div or less to 10 div or more |
| 延迟抖动 |
better than 1:20000 |
| 扫描放大 |
10 times (maximum sweep rate : 20ns/div) Note: 50ns/div, 20ns/div of A TIME BASE are uncalibrated |
10 times (maximum sweep rate : 10ns/div) |
| 准确度 |
+/-3%, additional error for magnifier +/-2% |
| 触发系统 |
触发模式 |
AUTO, NORM, TV-V, TV-H |
| 触发源 |
CH1,CH2,LINE,EXT |
| 耦合 |
AC |
| 倾斜率 |
+ OR - |
| TV-V, TV-H |
At least div or 1.0Vp-p Composite Sync. |
| 外部触发输入阻抗 |
1Mohm |
| 最大输入电压 |
250V (DC + Peak AC) |
| 灵敏度和频率/自动和标准 |
| |
20Hz-2MHz |
2MHz-20MHz |
| INT |
0.5div |
1.5div |
| EXT |
0.2Vp-p |
0.8Vp-p | |
| |
20Hz-2MHz |
2MHz-20MHz |
| INT |
0.5div |
1.5div |
| EXT |
0.2Vp-p |
0.8Vp-p | |
| |
20Hz-2MHz |
2MHz-20MHz |
| INT |
0.5div |
1.5div |
| EXT |
0.15Vp-p |
0.3Vp-p | |
| X-Y轴操作 |
X 轴 |
(Same CH1 except for the following) Deflection factor; same as that of CH1/Accuracy : +/-5%/Frequency response: DC to 500kHz (-3dB) |
| Y 轴 |
Same as CH2 |
| X-Y 轴相位相差 |
3º or less (at DC to 50MHz) |
| 直读功能 |
游标读数功能 |
Voltage reference △V: △-REF, Frequency reference 1/△T: △-REF |
| 面板设置显示 |
Verical axis CH1,CH2: V/div, UNCAL,MAG (converted value)
Note: displayed when the vertical mode is CH1,CH2,DUAL,ADD not displayed when the B node
Horizontal axis: S/DIV,UNCAL,MAG (converted value) |
| Effective Cursor Range from Center Graticule |
Vertical: within +/-3div, Horizontal: within +/-4div |
| 解析度 |
1/25 div |
| 数字储存功能 |
显示记忆体和储存记忆体 |
1000 Words/CH,1000 Words/CH x 2 |
| Acquisition Memory |
5us/div-20s/div: 2000 words/CH
0.2/div-20us/div: 1000 words/CH |
5us/div-20s/div: 2000 words/CH
0.1/div-2us/div: 1000 words/CH |
| 垂直解析度 |
25 point/div |
| 水平解析度 |
100 point/div |
| 最大取样速率 |
20MS/s |
| 数字频宽/单状态效应 |
5MHz |
| Repetitive Event |
20MHz |
40MHz |
60MHz |
| Data Acquisition Method |
NORM mode: storage the data each time trigger
AVG mode: averaging from 4 to 256 times
ROLL mode: data is continuously stored on the CRT
HOLD mode: data is held for the NORM, AVG.ROLL
SINGLE: wave form is held after stored
AMAG mode: simultaneously displaying the original waveform and its nagnified waveform
G-NG mode: judgement and comparing of acquisition signal |
| 储存数据 |
Up to two storage data can be saved.
Saved data can be recalled to the display whenever required. |
| Pre 触发 |
Variable (0.04 div step) |
| Plotter |
Plotter output of the CRT displayed information to an HP-GL.
Plotter via the RS-232C interface |
| 数据输出 |
RS-232C |
| Magnified Display |
X 10 by Time/div switch or MAG switch |
| X-Y 轴操作 |
Single trace X-Y X axis=CH1 * X axis=SA, Y axis=CH2 * Y axis=SB
Dual trace X-Y X axis=CH1 * Y axis=CH2
Sensitivity X axis:CH11 mV-5V/div +/-5% Y axis=CH2 1mV=5V/div+/-5%
Phase error 3° or less from DC-50kHz |
| Sweep Time |
0.2us/div-20s/div rejpetitive signal: 0.2us/div-2us/div
roll mode: 0.5s/div-20s/div ALT: 0.2us/div-0.5ms/div
CHOP: 1ms/div-20s/div |
0.1us/div-20s/div rejpetitive signal: 0.1us/div-2us/div
roll mode: 0.5s/div-20s/div ALT: 0.1us/div-0.5ms/div
CHOP: 1ms/div-20s/div |
| Readout Function |
(Panel setting display)
V/div, uncal, MAG, S/DIV, uncal, MAG
X-Y, Trigger point ,number of averaging , roll mode, smoothing, interpolation method,
save memory information, probe setting (cursor readout)
Voltage differnce △V: △-Ref, Time difference △T: △-Ref,
frequency 1/△T: △-Ref, Pre-trigger TRG: △ |
| 校准器 |
Probe Adjustmetn |
approx. 1kHz frequency, 0.5V(+/-3%) square wave duty ratio: 50% |
| 电源供应 |
Voltage Range / Frequency |
100,120,220,240, VAC +/-10%, 50/60Hz |
| 功率 |
approx. 65W |
| 物理参数 |
重量 |
approx. 8.5kg |
| 体积 |
320)W)×140(H)×430(L)mm |
| 环境参数 |
Temperature Range for Rated Operation |
+10℃ to +35℃ (+50℉ to 95℉) |
| Max. Ambient Operating Temperature |
0℃ to +40℃ (+32℉ to 104℉) |
| Max. Storage Temperature |
-20℃ to +70℃ (-4℉ to 158℉) |
| Humidity Range for Rated Operation |
45% to 85%RH |
| Max. Ambient Operating Humidity |
35% to 85%RH |
泰亚赛福 —— 世界领先的检测仪器集成供应商 
您当前的位置：
